CE Marking for Chinese Suppliers: Who Signs the Declaration

Last updated: 17 November 2026.

Direct answer. CE marking is the manufacturer's own declaration that a product meets the EU rules covering it — not an EU approval. The manufacturer runs the conformity assessment, builds the technical documentation, signs the declaration of conformity and affixes the mark. Importers must verify that before placing the product on the EEA market.

A Chinese factory that stamps CE on a part it has never assessed has not marked the product, it has created evidence against itself. The mark is a self-declaration with a paper trail behind it, and the paper trail is what an EU importer is legally required to check.

This page uses the European Commission's own CE marking guidance for manufacturers and for importers and distributors, retrieved on 17 November 2026. It describes obligations, not product scope: whether your specific part needs the mark depends on which EU legislation covers it, and that is a product-by-product question.

What the mark declares

The Commission describes the letters as signifying that products sold in the European Economic Area have been assessed to meet high safety, health and environmental protection requirements. By affixing it, a manufacturer declares that the product meets all the legal requirements for CE marking and can be sold throughout the EEA — and the same applies to products made outside the EEA.

Two limits matter as much as the declaration:

For a supplier, the second limit is the commercially useful one. Nobody on the buying side should treat the mark as a certificate, and a factory that markets it as one is describing the wrong document.

The six steps belong to the manufacturer

The Commission sets out six steps for a manufacturer affixing the mark. They are sequential, and each one produces something an importer can ask to see.

  1. Identify the applicable directives and regulations, and the harmonised standards. The Commission maintains the list of acts aligned with, or based on, Decision 768/2008/EC.
  2. Verify the product-specific requirements. One product can fall under more than one regulation or directive, and horizontal legislation on chemicals or the environment can apply as well.
  3. Identify whether an independent conformity assessment by a notified body is needed. For higher-risk products the manufacturer cannot check safety alone; a notified body appointed by national authorities performs the check, and the manufacturer may only affix the mark afterwards. Notified bodies are searchable in the NANDO database by legislation or by country.
  4. Test the product and check conformity. In most cases the notified body verifies the manufacturer's quality management, the product design and compliance with the essential requirements, and issues a certificate stating what was verified.
  5. Draw up and keep the technical documentation. It must be established before the application to a notified body or at the latest when the first unit of that type is placed on the market, and it must enable assessment of conformity.
  6. Affix the CE marking and draw up the EU declaration of conformity.

The sixth step is often described as a formality. It is the only step that produces a document with a signature on it, which is why it is the one an importer will ask for first.

What the declaration of conformity contains

The Commission lists the contents directly. The declaration must:

It is drawn up by the manufacturer, who declares under sole responsibility that the product conforms to the relevant regulation or directive. The Commission publishes a declaration of conformity template alongside the guidance.

Where the product is also covered by other EU legislation providing for CE marking, the accompanying documents must state that it conforms to those acts too. That sentence is worth reading twice on a multi-directive product, because a declaration that names one directive and silently ignores a second is a gap the importer inherits.

How the mark itself must look

The Commission's requirements on the physical mark are short and checkable:

RequirementWhat the guidance says
PlacementVisibly and legibly on the product, or where the nature of the product makes that impossible, on the packaging and the accompanying document
FormThe initials CE in the official form; the official drawing is published as GIF, PNG, JPG, AI and EPS
ProportionsWhere the mark is reduced or enlarged, the proportions of the graduated drawing must be respected
DimensionsComponents must have the same vertical dimension and may not be smaller than 5 mm
Notified body numberMust be displayed if a notified body was involved in the conformity assessment

Nothing here is discretionary. A moulded mark that has been squeezed below 5 mm to fit a small bracket is non-conforming on its own, whatever the assessment behind it says.

What the importer must check

The Commission's page for importers and distributors is where a Chinese supplier's documentation obligations become concrete. When importing from non-EU countries, the importer must check that products fulfil all EU safety, health and environmental requirements before placing them on the market, and must verify that:

Distributors carry a lighter but not empty duty: handle the product so as not to affect compliance, know which products must bear the mark, be able to identify non-compliant products, and be able to show national authorities confirmation from the manufacturer or importer that the necessary measures were taken.

One clause deserves particular attention from suppliers who sell under a customer's brand. If importers or distributors market products under their own names, they take over the manufacturer's responsibilities, and must therefore have sufficient information on design and production — because they assume the legal responsibility when affixing the mark. In that arrangement the factory is no longer the manufacturer in the sense the law uses, and the information flow has to support the party that is.

What to hand over, in practice

Taken together, the guidance implies a document pack that a Chinese supplier can assemble once and reuse:

Two common failures sit outside this list. The first is a declaration that cites a directive nobody checked against the actual product. The second is a supplier that cannot name the harmonised standards used in step one, which means step four has nothing to test against.

What this page does not tell you

Source note. Two first-party pages from the European Commission's DG for Internal Market, Industry, Entrepreneurship and SMEs, retrieved 17 November 2026, plus the CE marking landing page for the scope statement. These are the Commission's own guidance pages, not the legal texts. Verify the applicable directive with your importer and, where relevant, your notified body.

For the wider question of which conformity marks a Chinese part may need, the ASTM, CE and UL overview sets the marks side by side. Electrical and electronic parts usually raise the China RoHS versus EU RoHS question at the same time, and chemical restrictions are covered in the REACH and RoHS guide. If the destination market is the United States instead, the tariffs and landed cost guide covers the duty side. For documents a Chinese supplier normally issues, see the GB standards guide, and when the pack is ready the quotation route takes it. Inspection of the delivered lot is covered in the quality control guide.

Frequently asked questions

Does every product sold in the EU need CE marking?

No. The European Commission states that not all products must have CE marking: it is compulsory only for most of the products covered by the New Approach Directives, and it is forbidden to affix CE marking to other products.

Does the CE mark mean the EU approved the product?

No. The Commission states that CE marking does not indicate that a product has been approved as safe by the EU or by another authority, and it does not indicate the origin of a product.

Who signs the EU declaration of conformity?

The manufacturer draws up the declaration of conformity and declares under its sole responsibility that the product conforms to the relevant regulation or directive. The declaration carries the manufacturer name and address, essential characteristics of the product, the notified body identification number where applicable, and a legally binding signature.

How large must the CE mark be?

The Commission's guidance says the components of the CE marking must have the same vertical dimension and may not be smaller than 5 mm. If the mark is reduced or enlarged, the proportions of the official drawing must be respected.

Our EU customer is the importer. What must we give them?

The importer must verify that the manufacturer outside the EU has taken the necessary steps, that documentation such as the EU declaration of conformity and the technical documentation is available on request, and that contact with the manufacturer is possible at any time.

Sources

All sources retrieved 17 November 2026. This page is an independent reading of the sources listed; the official pages themselves are the specification.

Fact used on this pageSource
S1 — CE marking signifies assessment against safety, health and environmental requirements; manufacturer carries out the conformity assessment, sets up the technical file, issues the declaration and affixes the mark; two benefits for businesses and consumers; part of EU harmonisation legislation; Blue Guide referenceEuropean Commission, CE marking landing page, retrieved 17 November 2026 https://single-market-economy.ec.europa.eu/single-market/goods/ce-marking_en
S2 — Not all products must have CE marking; compulsory only for most products covered by the New Approach Directives; forbidden to affix to other products; CE marking does not indicate approval as safe by the EU or another authority and does not indicate originSame page, general guidelines note dated 25 October 2021, retrieved 17 November 2026 https://single-market-economy.ec.europa.eu/single-market/goods/ce-marking_en
S3 — Six manufacturer steps; role of harmonised standards and Decision 768/2008/EC; notified body route and NANDO; technical documentation timing and retention as specified in the applicable regulation or directive; declaration of conformity contents; placement, proportions and 5 mm minimumEuropean Commission, Manufacturers page, retrieved 17 November 2026 https://single-market-economy.ec.europa.eu/single-market/goods/ce-marking/manufacturers_en
S4 — Importer verification duties, distributor duties, and the takeover of manufacturer responsibilities when importers or distributors market under their own namesEuropean Commission, Importers and distributors page, retrieved 17 November 2026 https://single-market-economy.ec.europa.eu/single-market/goods/ce-marking/importers-and-distributors_en